High Quality HDPE Water Pipe and Fitting

HDPE (高密度ポリエチレン) Water Pipe and Fitting are components designed for joining, steering, branching or sealing polyethylene pipe systems, manufactured with high density polyethylene (HDPE) または中密度ポリエチレン (MDPE), perfectly compatible with PE pipes and widely used in the field of fluid transportation.

HDPE Water Pipe and Fitting Introduction

PE (ポリエチレン) pipe fittings are components designed for joining, steering, branching or sealing polyethylene pipe systems, manufactured with high density polyethylene (HDPE) または中密度ポリエチレン (MDPE), perfectly compatible with PE pipes and widely used in the field of fluid transportation.

HDPE Water Pipe and Fittingg アドバンテージ

1. 強い耐食性: resistance to acid and alkali, salt spray and chemical medium erosion, life span of more than 50 年.

2. Flexible impact resistance: adapt to ground settlement and low temperature environment, reduce the risk of tube explosion.

3. Light and easy to install: the weight is only 1/8 of the metal pipe fittings, supporting a variety of connection methods such as hot melt and electric melt.

4. Environmental protection and non-toxic: in line with drinking water sanitation standards (such as GB/T 17219), no heavy metal precipitation.

5. Low maintenance cost: 内壁は滑らかです, the friction resistance is small, and the long-term use is not easy to scale.

HDPE Water Pipe and Fitting Specifications

Gaskets: Gaskets are like rings used to seal connections between pipes. They come in different materials and shapes depending on the type of connection you have.

Pipe Elbows: Pipe elbows help change the direction of the pipe’s flow. They come in 90-degree and 45-degree angles, and there are two types: long radius (which is smoother) and short radius (which takes up less space but causes more pressure).

Pipe Bend: Pipe bends are like gentle curves in the pipe. They’re used when you need a smooth change in direction to avoid pressure build-up. They come in different sizes, like 3D and 5D, which refer to the curve’s length.

Pipe Tee: A pipe tee looks like the letter “T” and is used to split the flow of fluid from the main pipeline. There are different types, like straight tees (which have the same diameter), reducing tees (which have smaller branches), barred tees (used in special pipelines), and wye tees (which connect pipes at a 45-degree angle to reduce friction).

Cross: A cross looks like a plus sign and has one inlet and three outlets. It’s mainly used in fire sprinkler systems, not regular plumbing.

Pipe Reducers: Pipe reducers make a pipe narrower. There are two types: concentric and eccentric. Concentric ones keep the middle of the pipe at the same height. They’re used when two different pipe sizes need to be the same in the middle of a system. Eccentric ones help keep the bottom of the pipe at a certain level, so the outside surface of the pipe stays level.

Pipe Caps: At the end of a plumbing system, there’s a cap. It covers the end of the pipe to stop leaks.

Stub Ends: Stub ends do the same thing as pipe caps but are used with lap joint flanges.

Piping Unions: These are used for pipes with low pressure that need to be taken apart often. They have three parts: 女性の端, a male end, and a nut. The nut, along with the female and male ends, creates a strong seal.

Pipe Coupling: There are three types: full, half, and reducing. Full couplings connect small pipes. Half couplings connect a small pipe to a large one. Reducing couplings connect two pipes of different sizes.

HDPE Pipe Fitting Technical Standards

Welding pipe fitting: suitable for DN20-DN315, voltage 39.5V±0.5V, welding time automatic calibration.

Hot melt butt fitting: DN50-DN1200, heating plate temperature 210℃±10℃, pressure stage adjustable.

Mechanical connector: stainless steel clamp type, applicable pressure ≤1.6MPa, quick installation without tools.

HDPE Water Pipe and Fitting 応用

1. Municipal Engineering

Water supply pipe network: PE Tee, Flange socket, Water hammer impact resistance, Reduce leakage rate.

Gas transmission: Yellow PE gas pipe fitting, GB15558 certification, anti-static design.

2. 産業用 Sセナリー

Chemical pipeline: Acid and alkali resistant four-way and elbow, supporting PP/FRP composite lining.

鉱山排水: DN800 large diameter pipe fitting, resistant to ore particle wear.

3. Agriculture and E環境 Protection

点滴灌漑システム: Small-caliber PE bypass, precise distribution, water saving more than 30%.

Sewage collection: Seal ring reinforced inspection well connector, anti-leakage grade IP68.

梱包と発送

商品や数量により異なります,コイリングのパッキングを作ることができました,ロール,バンドル梱包,木箱または箱,等.

出荷:海沿い,鉄道,航空便または顧客の要求に応じて.

会社概要

洛陽大唐能源科技有限公司, 株式会社. 高品質のプラスチックパイプと継手を専門とする中国の大手メーカーです. 最先端の自動生産ラインを備え、チームによってサポートされています。 200 専門家, 私たちは以上を含む広範な製品ラインを提供しています 150 給水および排水システム用に設計されたプラスチック製のパイプおよび継手の種類, ガストランスミッション, および床暖房システム. 当社の主力製品には塩ビ管および継手などがあります。, PE (HDPE) パイプと継手, PPR パイプおよび継手, PEX床暖房パイプ。

ご不明な点がございましたら、HDPE Pipe Fitting, お気軽にお問い合わせください!

電話番号:0086-183 3790 0677

微信: 0086-183 3790 0677

ワッツアップ: 0086-183 3790 0677

電子メール: sales@pipesandfittings.net

支払い条件

T/T,一目でわかるL/C,ウエスタンユニオン & ペイパル,等.

HDPE Water Pipe and Fitting FAQ

Q1: How to choose the suitable PE pipe fittings specifications?

あ: ステップ 1: Confirm the pipe outer diameter (例えば. DE110) and SDR value (例えば. SDR11).

ステップ 2: Select PN rating according to system pressure (例えば. PN16 corresponds to 1.6MPa).

ステップ 3: Select the material according to the characteristics of the medium (gas requires yellow special parts).

第2四半期: What are the operation points of hot melt connection?

あ: Clean the pipe end to ensure that there is no oil;

Temperature of heating plate is controlled at 210±10℃;

Keep the butt pressure stage stable, do not move during cooling.

Q3: Can PE pipe fittings be mixed with PVC pipe?

あ:Direct connection is not recommended. It needs to be connected through a PE/PVC adapter and mechanically sealed with a flange or thread.

Q4: Do pipe fittings support custom non-standard dimensions?

あ: はい. Provide 3D scanning mapping services, can customize DN50-DN2000 shaped parts, lead time of 15-30 日.