HDPE פּייפּס בויען אַן עפעקטיוו וואַסער-שפּאָרן יראַגיישאַן סיסטעם

ווי גלאבאלע וואַסער דוחק פאַרשטאַרקן, עפעקטיוו וואַסער-שפּאָרן יראַגיישאַן סיסטעמען האָבן ווערן אַ האַרץ פאָדערונג אין אַגריקולטורע, לאַנדסקאַפּינג, און שטאָטיש אינזשעניריע. As a producer of HDPE פּייפּס מיט 20 יאָרן פון אינדוסטריע דערפאַרונג, we have summarized the golden rule of system design centered on HDPE pipes based on practical data from over 300 water-saving irrigation projects. This article will reveal how to increase irrigation efficiency by 30% and reduce leakage risk by 50% through scientific pipe network layout.

Why are HDPE pipes the core of water-saving irrigation systems?

1. Comparison of measured data: HDPE pipes vs. Traditional pipes

Leakage rate comparison: Cast iron pipe leakage rate > 12% per year, PVC pipe joint leakage rate 8%, HDPE hot melt welding achieves zero leakage (National Water Resources Research Institute 2023 data)

דינסט לעבן: Ordinary PVC pipes have a lifespan of 8-10 יאָרן, while HDPE pipes have a lifespan of up to 50 years in an environment of -60 ° C צו 60 ° סי

Flow retention rate: DN200 pipe has a pressure loss rate of only 3.2% over 20 יאָרן (certified data by German TUV)

2. גore advantages of HDPE pipes

Molecular-level sealing: Hot-melt welding forms molecular chain fusion, completely eliminating the risk of leakage at the interface

Dynamic pressure resistance: CRA pressure curves show that HDPE pipes can withstand 2.5 times instantaneous water hammer impacts

Terrain adaptability: 1500D bending radius enables seamless installation in complex terrains

Ecological safety: FDA food grade certified, heavy metal leaching < 0.001ppm

פינף important rules for designing Water-saving irrigation systems

Rule 1: Three-level pressure zoning control

High-pressure zone (> 0.6מפּאַ) : The main pipe is made of SDR11 series HDPE pipe with a wall thickness of ≥12.3mm

Medium pressure zone (0.4-0.6מפּאַ) : Branch pipes of SDR13.6 specification, equipped with pressure-compensating drippers

Low-pressure area (< 0.4מפּאַ) : The capillary network uses labyrinth drip irrigation tape with a working pressure of 0.1MPa

Rule 2: Precise hydraulic calculation model

Calculate head loss along the way using the Hazen-Williams formula:

  \ [h_f = 10.67 \ \ times times L Q ^ {} 1.852 / (C ^ ^ 1.852} {\ times D 4.8655} {) \)

  (C value is 150, HDPE pipe roughness 0.007mm)

Rule 3: Intelligent irrigation parameter configuration

Practical Tips for HDPE Pipe Layout (with 3D layout diagram analysis)

Tip 1: Terrain adaptive topology algorithm

Use “contour line encirsion” for pipe layout on slopes, and install pressure relief valves when the slope is greater than 15°

א “feng” shaped pipe network is implemented on the flat ground, with the spacing of branch pipes in a ratio of 1.2:1 to the range of nozzles

Tip 2: Key points for quality control of hot melt welding

210±5 ° C fusion temperature maintain pressure 0.15MPa

Heat absorption time = Pipe wall thickness (mm)×10 seconds, cooling time ≥ wall thickness (mm)×1 minute

Tip 3: Dynamic expansion compensation design

Set up Ω compensators every 50 מעטער, with a 5% extension allowance

The fixed piers are cast in C25 concrete, with dimensions = 3 times the pipe diameter

Practical case: 

A 3,000-mu cotton field project in Xinjiang achieved a 43% water saving and a 22% increase in yield per mu by using SDR17 series HDPE pipes and pressure-compensating drip irrigation tapes. The pipe network layout adopted the “three levels and four zones” מאָדעל, with the main pipes laid along the field ridges and the branch pipes spaced 56 מעטער, corresponding to a sprinkler range of 47 מעטער.

פour innovative combinations of the intelligent irrigation system

1. Integration of Internet of Things monitoring systems

Install soil moisture sensors every 200 מעטער

The electric valve is linked to the SCADA system with an error of less than 0.02MPa

2. Anti-clogging technical solution

Install a 120-mesh laminated filter at the head

The main pipe is designed with a 0.5% slope and a drain valve every 100 מעטער

3. Configuration of solar pumping stations

5kW photovoltaic system drives pipeline booster pump

With energy storage battery for 24-hour pressure stabilization

HDPE pipe selection guide with 20-year warranty

Quick reference table for selection parameters

Special reminder: Make sure to recognize the blue band marking. The density of PE100 grade raw materials should be ≥0.948g/cm³ to ensure compliance with the national standard GB/T13663.

סאַפּלייער

Luoyang Datang Energy Tech Co., לטד. איז אַ לידינג כינעזיש פאַבריקאַנט וואָס ספּעשאַלייזיז אין הויך-קוואַליטעט פּלאַסטיק פּייפּס און פיטינגז. יקוויפּט מיט שטאַט-פון-דעם-קונסט אָטאַמייטיד פּראָדוקציע שורות און געשטיצט דורך אַ קאָלעקטיוו פון 200 פּראָפעססיאָנאַלס, מיר פאָרשלאָגן אַ ברייט פּראָדוקט שורה מיט איבער 150 types of plastic pipes and fittings designed for water supply and drainage systems, גאַז טראַנסמיסיע, און שטאָק באַהיצונג סיסטעמען. אונדזער הויפּט פּראָדוקטן אַרייַננעמען פּווק פּייפּס און פיטינגז, פּע (HDPE) פּייפּס און פיטינגז, PPR פּייפּס און פיטינגז, און PEX פלאָר באַהיצונג פּייפּס.

Should you have any inquiries regarding PVC Pipe & פּע רער אין אַגריקולטוראַל יראַגיישאַן, ביטע טאָן ניט קווענקלען צו קאָנטאַקט אונדז!

טעל .:0086-183 3790 0677

וועטשאַט: 0086-183 3790 0677

ווהאַצאַפּפּ: 0086-183 3790 0677

בליצפּאָסט: sales@pipesandfittings.net