Բացատրված են փողային խողովակների կցամասերի չափերը: Թեմաներ, Չափերի և ընտրության ուղեցույց

Ճիշտ փողային կցամաս ընտրելը այնքան էլ պարզ չէ, որքան երկու թվերի համապատասխանությունը. Նշված կցամաս 1/2 դյույմ does not necessarily have a 1/2-inch thread diameter, and a fitting with a similar measured diameter may still use a completely different thread standard.

Understanding brass pipe fittings sizes, thread dimensions, nominal pipe size, and thread standards is essential when selecting brass elbows, թիեր, ագույցներ, ադապտերներ, hose connectors, and other threaded fittings.

This guide explains the most common brass fitting sizes, NPT and BSP threads, how to measure a brass fitting, and how to specify the correct size when ordering.

փողային խողովակների տեղադրում

What Does “փողային խողովակների տեղադրում Size” Actually Mean?

When suppliers or buyers refer to a brass fitting size, they are usually referring to the nominal connection size, not the actual physical diameter of the fitting.

Several different measurements may be involved:

Օրինակ, ա 1/2″ NPT brass fitting has a nominal size of 1/2 դյույմ, but its external thread major diameter is approximately 0.840 դյույմ (21.34 մմ).

This is why simply measuring a fitting with a caliper is not enough to identify its size.

Nominal Size vs. Actual Diameter

The nominal size is a standardized designation used to describe the pipe or connection. It should not automatically be interpreted as the actual thread diameter or pipe outside diameter.

For accurate identification, check the following together:

• Nominal fitting size
• Թեման ստանդարտ
• Male or female thread
• Thread major or internal diameter
• TPI or thread pitch
• Thread profile

Կարևոր: The dimensions in the following tables are standard reference dimensions for thread identification. Actual product dimensions can vary according to the applicable standard, tolerance, fitting design, and manufacturer.

Nominal Size vs. Actual Diameter

փողային խողովակների տեղադրում Size Chart

The most common brass pipe fittings are available in sizes ranging from small plumbing connections to larger industrial piping systems.

The following table provides common reference sizes for BSP threads:

These dimensions refer to the թել, not the overall outside diameter of the brass fitting.

Օրինակ, a 1/2″ BSP threaded fitting has a thread major diameter of about 20.955 մմ. The body of the elbow, թի, or coupling will normally be larger.

Common Brass Fitting Sizes

Սանտեխնիկայի համար, HVAC, ջուր, գազ, and general industrial applications, commonly requested brass fitting sizes include:

• 1/8″
• 1/4″
• 3/8″
• 1/2″
• 3/4″
• 1″
• 1-1/4″
• 1-1/2″
• 2″

Smaller sizes are common in instrumentation, small water lines, and hose connections, while larger sizes are frequently used in industrial and commercial piping.

1/2″ Փողային կցամասեր

NPT Brass Fitting Sizes

NPT (National Pipe Taper) is one of the most widely used inch-based pipe thread standards, particularly in North America.

NPT threads are tapered and use a 60-degree thread form. The thread dimensions are standardized under ASME B1.20.1.

A typical NPT brass fitting size chart is:

These are thread reference dimensions, not the overall dimensions of the fitting.

Օրինակ, if you measure approximately 21.3 mm across the external thread of a fitting, it may be a 1/2″ NPT thread. Այնուամենայնիվ, diameter alone does not prove that identification. TPI and thread profile should also be checked.

Why NPT Size Can Be Confusing

A common mistake is assuming:

1/2″ NPT = 1/2″ thread diameter

It does not.

1/2″ designation refers to the nominal pipe size, while the external thread diameter is approximately 0.840 դյույմ.

This difference is normal for pipe thread sizing and is one of the main reasons buyers should specify the complete thread standard when ordering brass fittings.

NPT Brass Fitting Sizes

BSP Brass Fitting Sizes

BSPP (Parallel) and BSPT (Tapered)

BSP—British Standard Pipe—is the dominant thread family in the UK, Եվրոպա, and many Commonwealth markets. Unlike NPT, BSP comes in two distinct forms:

BSPP (G thread, ISO 228-1): Parallel threads. They do not seal on the threads themselves. A separate sealing surface—usually a bonded washer, O-ring, or gasket—provides the seal.

BSPT (R/Rp thread, ISO 7-1): Tapered threads. Like NPT, BSPT seals by thread compression. Այնուամենայնիվ, the thread angle is 55 աստիճաններ (Whitworth form), not 60 աստիճաններ.

Common BSP Sizes

Thread dimensions per ISO 228-1 (BSPP) և ISO 7-1 (BSPT). Thread angle: 55° (Whitworth form). BSPP is parallel; BSPT is tapered at 1:16.

A common field observation: A thread measuring roughly 1/2 դյույմ (12.7 մմ) across the outside is likely a1/4″ BSP thread, not a 1/2″ BSP. 1/2″ BSP thread actually measures20.955 մմ across its major diameter. This “quarter-inch larger” rule of thumb holds approximately for BSP sizes up to about 1″, but always verify with a thread gauge rather than relying on visual estimation alone.

BSP Brass Fitting Sizes

NPT vs BSP: Why the Same Size May Not Fit

This is not a deep comparison—there is a dedicated article coming on that topic. But you need to know the essentials:

Never specify a brass fitting only as “1/2 inch.” Always confirm the thread standard.

Even when nominal sizes match—for example, both are labeled 1/2″—NPT (60° thread angle) and BSP (55° Whitworth) will not thread together properly. The 5° angle difference causes cross-threading and guarantees leaks. Forcing them together damages both threads.

How to Measure a Brass Pipe Fitting

When you have an unmarked fitting in hand, five measurements will identify it:

Քայլ 1: Check the Fitting Type

Անկյուն, թի, զուգավորում, ադապտեր, or connector? The type tells you what the fitting does, but not its size.

Քայլ 2: Measure the Thread Diameter

Use a vernier caliper. For male threads, measure across the outside diameter at the widest point. For female threads, measure the inside diameter.

Քայլ 3: Count the Threads (TPI)

Use a thread pitch gauge or place a ruler along the thread and count how many complete threads fit within one inch. This is the TPI.

Քայլ 4: Identify the Thread Profile

Tapered or parallel? NPT and BSPT taper; BSPP and metric threads are parallel. Roll the fitting on a flat surface—a tapered thread will wobble visibly.

Քայլ 5: Check Male or Female

A thread identification kit containing pitch gauges, a caliper, and reference profiles is worth the investment if you regularly handle mixed-standard fittings.

Measure a Brass Pipe Fitting

How to Choose the Right Brass Fitting Size

Once you understand what the size number actually means, selection becomes systematic. Run through these seven checks before placing an order:

Common brass grades for fittings include CW617N (CuZn40Pb2) for general-purpose plumbing and CW602N (CuZn36Pb2As) for dezincification-resistant applications in aggressive water conditions.

Brass Fittings in industrial applications

Common Mistakes When Choosing Brass Fitting Sizes

Սխալ 1: Treating Nominal Size as Actual Diameter

A 1/2″ fitting does not necessarily have a 1/2-inch thread diameter.

Սխալ 2: Measuring Only the Fitting Body

The body diameter does not identify the thread size.

Սխալ 3: Ignoring NPT vs. BSP

A similar diameter does not mean the threads are compatible.

Սխալ 4: Confusing BSPP and BSPT

Both belong to the BSP family, but one is parallel and the other is tapered.

Սխալ 5: Ignoring Male/Female Configuration

A correct thread size is not enough if the connection gender is wrong.

Սխալ 6: Selecting by Diameter Without Checking TPI

Two threads can have similar diameters but different pitches or TPI.

Փողային կցամասեր Size vs Pipe Size: Are They the Same?

No—and this is where the confusion peaks.

A fitting marked 1/2″ does not have a 12.7 mm thread OD. In NPT, the 1/2″ size has a 0.840″ thread OD. In BSP, the 1/2″ size has a 20.955 mm major diameter. The nominal size is a matching reference, not a physical dimension.

Brass Fitting Size vs Pipe Size

Need փողային խողովակների կցամասեր for Your Project?

Need brass pipe fittings in specific sizes, thread standards, or connection types? Share your required fitting type, nominal size, թելերի ստանդարտ, նյութական, and application with our team. Luoyang Datang Energy Tech Co., ՍՊԸ will confirm the appropriate specification and provide a quote.

[Request a Quote →]