HDPE торбалары эффектив су саклаучы сугару системасы төзи

As global water shortages intensify, efficient water-saving irrigation systems have become a core demand in agriculture, landscaping, һәм муниципаль инженерия. As a producer of HDPE торбалар with 20 years of industry experience, we have summarized the golden rule of system design centered on HDPE pipes based on practical data from over 300 water-saving irrigation projects. This article will reveal how to increase irrigation efficiency by 30% and reduce leakage risk by 50% through scientific pipe network layout.

Why are HDPE pipes the core of water-saving irrigation systems?

1. Comparison of measured data: HDPE pipes vs. Traditional pipes

Leakage rate comparison: Cast iron pipe leakage rate > 12% per year, PVC pipe joint leakage rate 8%, HDPE hot melt welding achieves zero leakage (National Water Resources Research Institute 2023 мәгълүматлар)

Хезмәт вакыты: Ordinary PVC pipes have a lifespan of 8-10 еллар, while HDPE pipes have a lifespan of up to 50 years in an environment of -60 ° C дан 60 ° C.

Flow retention rate: DN200 pipe has a pressure loss rate of only 3.2% бетте 20 еллар (certified data by German TUV)

2. C.ore advantages of HDPE pipes

Molecular-level sealing: Hot-melt welding forms molecular chain fusion, completely eliminating the risk of leakage at the interface

Dynamic pressure resistance: CRA pressure curves show that HDPE pipes can withstand 2.5 times instantaneous water hammer impacts

Terrain adaptability: 1500D bending radius enables seamless installation in complex terrains

Экологик куркынычсызлык: FDA food grade certified, heavy metal leaching < 0.001ppm

Биш important rules for designing Water-saving irrigation systems

Rule 1: Three-level pressure zoning control

High-pressure zone (> 0.6MPa) : The main pipe is made of SDR11 series HDPE pipe with a wall thickness of ≥12.3mm

Medium pressure zone (0.4-0.6MPa) : Branch pipes of SDR13.6 specification, equipped with pressure-compensating drippers

Low-pressure area (< 0.4MPa) : The capillary network uses labyrinth drip irrigation tape with a working pressure of 0.1MPa

Rule 2: Precise hydraulic calculation model

Calculate head loss along the way using the Hazen-Williams formula:

  \ [h_f = 10.67 \ \ times times L Q ^ {} 1.852 / (C ^ ^ 1.852} {\ times D 4.8655} {) \)

  (C value is 150, HDPE pipe roughness 0.007mm)

Rule 3: Intelligent irrigation parameter configuration

Practical Tips for HDPE Pipe Layout (with 3D layout diagram analysis)

Tip 1: Terrain adaptive topology algorithm

Use “contour line encirsion” for pipe layout on slopes, and install pressure relief valves when the slope is greater than 15°

А. “feng” shaped pipe network is implemented on the flat ground, with the spacing of branch pipes in a ratio of 1.2:1 to the range of nozzles

Tip 2: Key points for quality control of hot melt welding

210±5 ° C fusion temperature maintain pressure 0.15MPa

Heat absorption time = Pipe wall thickness (мм)×10 seconds, cooling time ≥ wall thickness (мм)×1 minute

Tip 3: Dynamic expansion compensation design

Set up Ω compensators every 50 метр, with a 5% extension allowance

The fixed piers are cast in C25 concrete, with dimensions = 3 торба диаметры

Practical case: 

A 3,000-mu cotton field project in Xinjiang achieved a 43% water saving and a 22% increase in yield per mu by using SDR17 series HDPE pipes and pressure-compensating drip irrigation tapes. The pipe network layout adopted the “three levels and four zones” model, with the main pipes laid along the field ridges and the branch pipes spaced 56 метр, corresponding to a sprinkler range of 47 метр.

F.our innovative combinations of the intelligent irrigation system

1. Integration of Internet of Things monitoring systems

Install soil moisture sensors every 200 метр

The electric valve is linked to the SCADA system with an error of less than 0.02MPa

2. Anti-clogging technical solution

Install a 120-mesh laminated filter at the head

The main pipe is designed with a 0.5% slope and a drain valve every 100 метр

3. Configuration of solar pumping stations

5kW photovoltaic system drives pipeline booster pump

With energy storage battery for 24-hour pressure stabilization

HDPE pipe selection guide with 20-year warranty

Quick reference table for selection parameters

Special reminder: Make sure to recognize the blue band marking. The density of PE100 grade raw materials should be ≥0.948g/cm³ to ensure compliance with the national standard GB/T13663.

Тапшыручы

Luoyang Datang Energy Tech Co., ООО. югары сыйфатлы пластик торбалар һәм җиһазлар буенча махсуслашкан Кытай җитештерүче әйдәп баручысы. Заманча автоматлаштырылган җитештерү линияләре белән җиһазландырылган һәм коллектив ярдәме белән 200 профессионаллар, без киң продукт линиясен тәкъдим итәбез 150 types of plastic pipes and fittings designed for water supply and drainage systems, газ җибәрү, идән җылыту системалары. Безнең төп продуктларга ПВХ торбалар һәм җиһазлар керә, ЭЭМ (HDPE) Торбалар һәм җиһазлар, PPR торбалар һәм җиһазлар, һәм PEX идән җылыту торбалары.

ПВХ торба турында соравыгыз булса & Авыл хуҗалыгы сугаруында торба, зинһар, безнең белән элемтәгә керергә курыкмагыз!

Тел.:0086-183 3790 0677

Вечат: 0086-183 3790 0677

Ватсап: 0086-183 3790 0677

Электрон почта: sales@pipesandfittings.net