ایچ ڈی پی ای پائپ پانی کی بچت کا ایک موثر نظام بناتے ہیں۔

جیسے جیسے عالمی سطح پر پانی کی قلت شدت اختیار کر رہی ہے۔, آبپاشی کے موثر نظام زراعت میں بنیادی ضرورت بن چکے ہیں۔, زمین کی تزئین کی, اور میونسپل انجینئرنگ. As a producer of ایچ ڈی پی ای پائپ with 20 صنعت کے تجربے کے سال, we have summarized the golden rule of system design centered on HDPE pipes based on practical data from over 300 water-saving irrigation projects. This article will reveal how to increase irrigation efficiency by 30% and reduce leakage risk by 50% through scientific pipe network layout.

Why are HDPE pipes the core of water-saving irrigation systems?

1. Comparison of measured data: HDPE pipes vs. Traditional pipes

Leakage rate comparison: Cast iron pipe leakage rate > 12% per year, PVC pipe joint leakage rate 8%, HDPE hot melt welding achieves zero leakage (National Water Resources Research Institute 2023 data)

سروس کی زندگی: Ordinary PVC pipes have a lifespan of 8-10 سال, while HDPE pipes have a lifespan of up to 50 years in an environment of -60 ° C سے 60 ° C

Flow retention rate: DN200 pipe has a pressure loss rate of only 3.2% over 20 سال (certified data by German TUV)

2. سیore advantages of HDPE pipes

Molecular-level sealing: Hot-melt welding forms molecular chain fusion, completely eliminating the risk of leakage at the interface

Dynamic pressure resistance: CRA pressure curves show that HDPE pipes can withstand 2.5 times instantaneous water hammer impacts

Terrain adaptability: 1500D bending radius enables seamless installation in complex terrains

Ecological safety: FDA food grade certified, heavy metal leaching < 0.001پی پی ایم

Five important rules for designing Water-saving irrigation systems

Rule 1: Three-level pressure zoning control

High-pressure zone (> 0.6ایم پی اے) : The main pipe is made of SDR11 series HDPE pipe with a wall thickness of ≥12.3mm

Medium pressure zone (0.4-0.6ایم پی اے) : Branch pipes of SDR13.6 specification, equipped with pressure-compensating drippers

Low-pressure area (< 0.4ایم پی اے) : The capillary network uses labyrinth drip irrigation tape with a working pressure of 0.1MPa

Rule 2: Precise hydraulic calculation model

Calculate head loss along the way using the Hazen-Williams formula:

  \ [h_f = 10.67 \ \ times times L Q ^ {} 1.852 / (C ^ ^ 1.852} {\ times D 4.8655} {) \)

  (C value is 150, HDPE pipe roughness 0.007mm)

Rule 3: Intelligent irrigation parameter configuration

Practical Tips for HDPE Pipe Layout (with 3D layout diagram analysis)

ٹپ 1: Terrain adaptive topology algorithm

استعمال کریں۔ “contour line encirsion” for pipe layout on slopes, and install pressure relief valves when the slope is greater than 15°

اے “feng” shaped pipe network is implemented on the flat ground, with the spacing of branch pipes in a ratio of 1.2:1 to the range of nozzles

ٹپ 2: Key points for quality control of hot melt welding

210±5 ° C fusion temperature maintain pressure 0.15MPa

Heat absorption time = Pipe wall thickness (ملی میٹر)×10 seconds, cooling time ≥ wall thickness (ملی میٹر)×1 minute

ٹپ 3: Dynamic expansion compensation design

Set up Ω compensators every 50 میٹر, with a 5% extension allowance

The fixed piers are cast in C25 concrete, with dimensions = 3 times the pipe diameter

Practical case: 

A 3,000-mu cotton field project in Xinjiang achieved a 43% water saving and a 22% increase in yield per mu by using SDR17 series HDPE pipes and pressure-compensating drip irrigation tapes. The pipe network layout adopted the “three levels and four zones” model, with the main pipes laid along the field ridges and the branch pipes spaced 56 میٹر, corresponding to a sprinkler range of 47 میٹر.

ایفour innovative combinations of the intelligent irrigation system

1. Integration of Internet of Things monitoring systems

Install soil moisture sensors every 200 میٹر

The electric valve is linked to the SCADA system with an error of less than 0.02MPa

2. Anti-clogging technical solution

Install a 120-mesh laminated filter at the head

The main pipe is designed with a 0.5% slope and a drain valve every 100 میٹر

3. Configuration of solar pumping stations

5kW photovoltaic system drives pipeline booster pump

With energy storage battery for 24-hour pressure stabilization

HDPE pipe selection guide with 20-year warranty

Quick reference table for selection parameters

Special reminder: Make sure to recognize the blue band marking. The density of PE100 grade raw materials should be ≥0.948g/cm³ to ensure compliance with the national standard GB/T13663.

فراہم کنندہ

Luoyang Datang Energy Tech Co., لمیٹڈ. ایک سرکردہ چینی صنعت کار ہے جو اعلیٰ معیار کے پلاسٹک کے پائپوں اور متعلقہ اشیاء میں مہارت رکھتا ہے۔. جدید ترین خودکار پروڈکشن لائنوں سے لیس اور ایک ٹیم کی طرف سے تعاون یافتہ 200 پیشہ ور افراد, ہم پر مشتمل ایک وسیع پروڈکٹ لائن پیش کرتے ہیں۔ 150 types of plastic pipes and fittings designed for water supply and drainage systems, گیس کی ترسیل, اور فرش حرارتی نظام. ہماری اہم مصنوعات میں پیویسی پائپ اور متعلقہ اشیاء شامل ہیں۔, PE (ایچ ڈی پی ای) پائپ اور متعلقہ اشیاء, پی پی آر پائپ اور متعلقہ اشیاء, اور PEX فلور ہیٹنگ پائپس.

کیا آپ کو پیویسی پائپ کے بارے میں کوئی پوچھ گچھ کرنی چاہئے۔ & زرعی آبپاشی میں پیئ پائپ, براہ کرم ہم سے رابطہ کرنے میں سنکوچ نہ کریں۔!

ٹیلی فون:0086-183 3790 0677

Wechat: 0086-183 3790 0677

واٹس ایپ: 0086-183 3790 0677

ای میل: sales@pipesandfittings.net